Pz IV Ausf J - WIP (Tamiya)

Hope to finally get this one across the finish line.

M3A1 mit wurf pt. III

Some small additional progress - added notek light and cable on front fender; Ger. fu radio and antenna.  Visors on windshield armor plate and top of doors need to be added but getting close.  Additional crew figure with MG34 temporarily placed.

M3A1 Halftrack with wurfrahmen 40 pt. II

Slightly more progress.  Added a cannibalized roof dry-fitted in place.

The wurf test-fitted into place.

M3A1 Halftrack with wurfrahmen 40

This is the Dragon IDF M3 Halftrack with Nord missile system rebuilt into a beute M3A1 halftrack with wurfrahmen 40 serving with 11. Panzerdivision based on references from the division's surrender in 1945.  According to references, the M3A1 joined the divisions TOE sometime in 12/1944.  Replacing the kit's Nord four missile system with four 28 cm Wurfkörper Spreng wurfrahmen 40 taken from the Dragon Sd.Kfz. 251 Ausf D. kit in sort of a retro version of the IDF vehicle.  (Note that the IDF kit contains all of the parts for the back ordered/hard to find original WW2 vintage M3A1 halftrack kit (other than decals), including the .50 cal and "pulpit".)

The initial paint coats are Mission Model's paint US Army Olive Drab.  Will have some German camouflage overspray (esp. over where the US markings would have been), although the reference pictures leave room for interpretation.  Most likely will use green/brown (either olivgrun and rotbraun, or the nicer looking (IMO) Nato green/brown), with some dunkelgelb "stick" overspray (seemingly mainly over the doors).  Some sort of roof also was installed over the driver's area, so may cannibalize the full-length roof provided for the IDF Nord M3.  Lots more to do, but thus far kit has gone together well, although the tracks are a little tricky to install (will leave off outer half of return roller before installing track if build another version).

Did a color sample (albeit brushed) of olivgrun versus Nato Green, and rotbraun vs. Nato Brown.  Also, found some 35+ year old USAF decals - maybe for a 1/32 P-51? - and crudely cut out the star portions and some over sized numbers.  These will be overpainted, so crudeness should be okay - I hope.

SU-100 WIP (Update)

Getting a little bit closer to the finish line on the Dragon SU-100 ("Arab" version built as circa 1945 SU-100 in Vienna (Wien)).  Have put down two initial coats of Mission Model Paints #031 – Russian Dark Green 4BO FS 34079.  Will need touch up wheels, base coat.  Also, a few parts, such as the exhausts, driver's hatch details, etc. need to be added.  May leave fuel tanks and tow cables or tracks off, as the reference vehicles seem to lack many of the same.  Fenders have been removed.  Hatches are tentatively in open position.  Still deciding as to whether to replace first road wheel on drive side with half-spider per Wien museum example (not clear when change occurred on original as typically SU-100 in 1945 saw only limited service and typically had a full set of solid disc wheels).

Panzergrau

Initial base coat of Mission Model Panzergrau on ICM [Mercedes] L3000S and Tamiya Sd.Kfz. 232.

Some clean up need, but plan to high-light with Mission Models Light Ghost Grey on one and (maybe) Mission Models British Slate Grey on the other.

WIP T-34/76 UZTM, T-34/76 Factory 112, KV-1 and SU-100 Lots of Red Army AFVs

The Trumpeter KV-1 Model 1942 Heavy Cast Turret is a very nice kit, at a good price.  It was easy and quick to assemble with optional length and link tracks.  P/E grills for the exhaust (included in TR's Model 1939 kit) might have been nice, but not 100% necessary.  Note that it actually represents a model 1941 with early cast turret.  Started to paint using Mission Model's Russian Dark Olive 2 FS 34096, and MM's tire black (kind of a grey) for the tracks.

The DML "formachka" aka UZTM turret is described in a previous entry and it also is starting to be painted with Russian Dark Olive 2 FS 34096, and MM's tire black (kind of a grey) for the tracks and rubber wheels.

On the extreme right and below is the DML T-34/74 with Commander's Cupola Factory 112.  This is a nice kit but need to really think about the end result and consult references before proceeding.  OOB, the instructions would have you build an early hull (c. 1942) but with with a late (c. 1943) turret.  After looking through references, the intent is to build a late 1943 Factory 112 version.  All of the parts needed are in the box, but lack of advanced planning created problems.  For the hull, should use the straight edged glacis plate, not the interlocking one (realized too late), as well as moving the headlight to the fender (if you use the straight edged plate, there will be no headlight mounting hole to plug), using the "hammerhead" towing mounts (non-integrated version) and armored bow MG.  The side hull grab handles can be used per instructions, as can the radio mount, but the two front grab handles should be straight, not angled.  Also, there should be a deflection strip below the driver's hatch.  On the turret, the casting number probably should be higher.  For late 1943 models, the 90 angled turret grab handles appear to be more common that the P/E version called out by the instructions (see UZTM handles).  The cylindrical external fuel tanks also would be appropriate.  For a very late/final (1944) version, on the turret, the lifting rings can be replaced with lifting hooks (e.g, from a T-34/85 sprue) and the hull grab handles appear to be modified to be shorter with the last two on each side displaced higher to accommodate the fuel tanks.

This the DML Arab/Egyptian, in construction as a very early version SU-100 (c. 1945 Austria).  Changes include deletion of the storage box on the starboard fender (apparently a post-war, largely Czech (?)) addition, using the old-style commander's split hatch, and using the split loader's hatch (a very early feature).  There is no gun breech or any other interior detail. so not sure about which hatches to leave open, but would like to at least have commander and loader's occupied to break up the solidity of the hull.  A front half-spider wheel replacement also might add some visual interest - present on the Vienna exemplar, but no contemporary pictures of the same and has been commented that because the SU-100 was such a late introduction, most did not suffer wheel damage which would have necessitated replacing one or more of the "factory" wheels.  In addition, on the early SU-100, the rear and side plates of the fighting compartments did not have the nice overlapping plates contained in the kit, but a rather rough junction (as per exemplar from Vienna).

Preliminary base coat of Mission Model 4BO.

Mini Art ZIS-3 aka 7.62 cm Feldkanone 288(r)

WIP of the ZIS-3 aka 7.62 cm Feldkanone 288(r) by Mini Art, in towing mode  Generally went together without trouble, although some parts are delicate and barrel is two-part.  Painted using Mission Models dunkelgelb with a very light olivegrun camo pattern on the gun shield

Dragon Sd.Kfz. 251/? Ausf. D mit 2.8 cm Pz.B. 41

WIP of the recent Dragon Sd. Kfz. 251/1 Ausf. D mit Wurfrahmen 40 (#6861).  Decided to leave off the Wurf. 40 and add the 2.8 cm Pz.B. 41 from the Dragon Sd. Kfz. 251/7 Ausf. D (#6223).  May not have been a "standard" modification, but rather a possible field modification by 12. SS-Pz. Div. in France, 1944.  From reference pictures of the vehicle (lic. SS-193932), unclear (at least to me) as to whether base vehicle is /1 or /7 due to branches, crew etc.

Started painting using Mission Models dunkelgelb as base with olivgrun and a rot braun/NATO brown overspray.